Deliverable 01 · Photo set
Photographs of every defect
Close enough to see the damage, wide enough to show where it sits on your roof.
Victoria, Texas
Victoria Commercial Roof Coatings — Silicone & Polyurea Systems
If your Victoria building has a sound flat roof you'd rather restore than tear off, here's the honest first step.
ARP's Victoria office restores commercial flat roofs across the Crossroads with silicone and polyurea coating systems installed over your existing roof — no tear-off, no landfill trip. ARP runs one of the few polyurea spray rigs statewide and applies manufacturer-certified systems with 20-year warranties on eligible substrates. The first move is a moisture scan and a written scope.
Family owned, locally accountable
COO & President — the father and son behind ARP
Why these credentials are on this page
5,000+
Completed projects
4.9★
300+ five-star reviews
GAF GoldElite Commercial
Manufacturer standing
UNIFLEX Premier Elite
Restoration coatings
BBB A+ · CTRCA Member
Accountability
Why Restore
Why Victoria property managers restore instead of replacing
Here's the thing most coating bids won't put in writing, and it's the first thing ARP's commercial roofing in Victoria team tells you: a restoration coating is a capital decision, and you're the one who has to explain it to ownership. Get it wrong — coat a roof that was already too far gone — and you've spent six figures sealing water inside the building. Get it right, and you've turned a tear-off that would've been a capital project into an operating expense your ownership can budget the same year.
That's why our Victoria team starts every coating with a moisture scan, not a quote. If the deck and seams under your membrane are still sound, a coating is often the right call. If the insulation is holding water, we'll tell you so and point you toward a commercial roof replacement instead. A coating restores a roof that has good bones left; it cannot fix a saturated or failed deck, and we won't pretend otherwise.
The reason we can carry the harder systems is equipment. Polyurea takes a spray rig that runs six figures to buy and maintain — we're one of the few crews running one across the state. We've coated buildings like the Victoria Fire Station, where a seamless system went down over an occupied building without disrupting operations.
We restore roofs across the Crossroads and along the coast — Port Lavaca, Port O'Connor, and the Gulf-facing buildings where a seamless silicone or polyurea skin earns its keep against salt air and wind-driven rain.
I reach for polyurea two ways. One is an old gravel built-up roof, where it bonds seamless over the aggregate and thinner coatings won't hold. The other is any owner who wants the strongest, most durable roof they can put on the building, one built to stand the test of time. Polyurea goes over gravel, TPO, modified bitumen, even metal, and turns whatever is already up there into one seamless waterproof membrane. And it is renewable: when the surface wears you recoat it instead of tearing off, so spec it right the first time and you may never buy another roof.
Randal Williams · COO, ARP Roofing & Remodeling
Coating Chemistry
Which coating chemistry should you put on your Victoria roof?
Straight up — it comes down to two systems, and the roof decides which one. Both are certified systems, not paint.
| System | What it does best | Where it fits |
|---|---|---|
| Silicone | Ponding-tolerant and reflective, which matters in the Crossroads heat | A strong restoration over a sound single-ply or modified-bitumen roof |
| Polyurea | The most durable system we install — seamless and hail-resistant | Bonds over gravel built-up, metal, and single-ply where thinner coatings won't |
You'll notice acrylic isn't on that short list. We're certified to install it, but in Victoria's heat and coastal moisture we steer away from acrylic coatings — they're less durable than silicone or polyurea and don't tolerate ponding and humidity nearly as well, so on a Gulf-adjacent roof they're the wrong long-term bet.
One thing worth knowing: polyurea is a separate system, not a UNIFLEX or Elevate product. We hold UNIFLEX Premier Elite and Elevate Red Shield certifications for their acrylic and silicone restoration systems, and we install manufacturer-certified polyurea — our premier fluid-applied system from several other manufacturers — systems that carry FM Global and Miami-Dade product approvals and 20-year warranties on eligible substrates.
Cost-wise, most Victoria coating projects land between $5.65 and $10.30 per square foot installed depending on the system (silicone at the low end, polyurea at the high). The FAQ below breaks the numbers down; for how coating pricing works across every variable, see our commercial roof coatings systems and pricing guide.
How a Victoria
How a Victoria coating project actually runs
Three stages, and the first one is where the honest answer lives.
- Assessment — we run a moisture scan (or cut cores) to confirm the roof is a restoration candidate, then hand you a written scope before anyone quotes a number.
- Prep and detail work — the roof gets cleaned, seams and penetrations get reinforced, and any localized repairs happen before a drop of coating goes down.
- Application and warranty — the crew we deploy and supervise sprays the system, we register the manufacturer warranty, and we walk the finished roof with you.
The Right Fit
Is a coating the right fit for your building?
A coating probably fits if you:
- Still have a sound deck
- Are weighing a restoration against a full replacement
- Have had ponding water as the recurring headache
A coating is probably not the fit if:
- The insulation is already saturated
- The deck is failing
- The lowest bid in town is the only number that matters — a coating over a wet roof is money you spend twice
Estimate your Victoria project
What a roof coating costs in Victoria
A restoration coating is priced per square foot of an eligible substrate — a fraction of a tear-off. Price your building against our 2026 Victoria rates, then we'll confirm the substrate is coating-eligible on the roof.
| System | Installed / sq ft | Where it fits |
|---|---|---|
| GAF EverGuard TPO / single-ply | $8.24 to $14.42 | Low-slope membrane, heat-welded seams |
| Commercial metal (site-formed) | $11.33 to $18.54 | Standing-seam for steeper commercial roofs |
| Silicone / acrylic restoration coating | $3.60 to $6.18 | Restoration-eligible substrate only |
| Flat-priced commercial repair | $1,500 to $3,600 per job | Priced after an on-roof inspection |
Read the units
Ranges are per square foot of actual roof area — the low-slope or steep surface a crew installs. Flat-priced repair is per job, not per foot. Coating rates assume a restoration-eligible substrate confirmed on the roof.
Price your Victoria roof & book the visit
2026 Victoria rates. About 40 seconds.
Roof area used: 12,000 sq ft — low-slope roofs run close to footprint
Adjust roof size to see your price
Your 2026 Victoria range
Request in — we'll text to confirm
Need it sooner? Call or text (361) 238-4255.
Four things move your number
Driver 01
Roof size and pitch
Steeper means slower and safer, which costs more.
Driver 02
Material
The single biggest lever, and the one you actually choose.
Driver 03
Decking condition
Found at tear-off, photographed, and shown to you before any replacement.
Driver 04
Access
If your roof is hard to reach or the property is tight.
Honest fit check
Is ARP the right fit for your Victoria project?
The best way to judge any Victoria contractor — us or anyone else — is to ask for a written scope, ask who your single point of contact is, and ask when the manufacturer warranty gets registered in your name. If a roofer can't answer those three plainly, that's your answer.
Yes — we're a match
A good fit if you
- Want a roofer your Victoria neighbors have actually used — not a pop-up tent after the last hailstorm.
- Want everything documented and in writing, with photos, before any crew gets on the roof.
- Plan to stay in your Victoria home or hold the property long term.
- Had recent hail or wind damage and want it documented correctly for your carrier.
No — we'll say so up front
Not the right fit if you
- Need a commercial job below our minimum repair scope, or a firm residential repair price over the phone — we quote every repair after an on-roof inspection.
- Need someone to start tomorrow with no inspection.
- Are choosing purely on the lowest bid, without reading the scope underneath it.
- Want a contractor to pay, waive or "take care of" your deductible — a criminal offense in Texas under Business & Commerce Code § 27.02.
We'd rather tell you that on the phone than waste a walkthrough.
No cost, no obligation
Your free Victoria commercial roof assessment
A free Victoria commercial roof assessment costs nothing and comes with no obligation. A project manager inspects the membrane or metal, checks it where it matters, and gives you a written report on whether a coating is the right restoration — or whether it isn't.
A coating only works over a roof that's sound enough to hold it. We check the substrate, the seams, and the drainage first, and we'll tell you plainly when a coating would just buy a few months over a roof that needs more.
You get the photos and the scope whether you hire us or not, and on commercial work that scope is COO-reviewed before anything starts.
From assessment to warranty
1
Free Storm Shield Assessment
We measure your roof, photograph it, and document what's actually there — not a curbside guess. You get the photo set whether you hire us or not.
2
Written Scope Before Any Work
You'll see line-item scope, materials, warranty options, and a real number in writing. On commercial projects that document is COO-reviewed. Nothing starts until you've read it.
3
Install and Warranty Registration
A crew led by an ARP project manager does the work, pulls the Victoria permit, and inspects at the key stages — then your manufacturer warranty registers in your name within 30 days.
No fee, no deposit, no pressure. We confirm your address is covered before we schedule — then a project manager walks the roof.
Questions that decide the job
Victoria roofing — frequently asked questions
How much does a commercial roof coating cost in Victoria?
+
A commercial roof coating in the Victoria market runs about $5.65–$7.20 per square foot for silicone and $7.20–$10.30 per square foot for polyurea installed, so a 10,000-square-foot roof typically lands between $56,500 and $103,000. Your number depends on the existing roof's condition, the system chosen, and how much detail repair the seams and penetrations need.
What is the longest-lasting roof coating?
+
Polyurea is the most durable and longest-lasting coating system we install — a properly specced polyurea system lasts 20 to 40-plus years, with a fresh top coat reapplied roughly every 18 to 20 years to keep the clock running. It cures into one seamless, hail-resistant waterproof membrane over gravel, metal, or single-ply, and it's renewable — when the surface wears, you recoat instead of tearing off. Silicone is the strong second choice, especially where ponding water is the recurring problem.
What are the drawbacks of silicone roof coating?
+
Silicone's main drawbacks are that it holds dirt over time (which can dull its reflectivity), it gets slippery when wet, and once it's cured, almost nothing except more silicone will bond to it — so future recoats are locked into the same chemistry. The trade-off is worth it on ponding-prone roofs, where silicone's water tolerance outperforms other systems. We'll tell you honestly whether your roof is a silicone candidate before you commit.
Still exploring?
Want the complete guide to commercial roof coatings?
Our statewide commercial roof coatings guide goes deep on materials, cost, lifespan, and how each choice holds up in Texas — the full answers behind this Victoria page.
Explore your Victoria roof
Start where your question is
Every door lands on one written scope — pick the one that fits where you are right now.
01
Victoria Commercial Gutters
ARP installs commercial box gutters, oversized downspouts, and internal roof drainage for Victoria, TX buildings from our Victoria office. Free assessments.
See Victoria Commercial Gutters →02
Victoria Commercial Metal Roofing
If your Victoria warehouse, shop, or storefront needs metal that lasts, here's what to weigh before you sign.
See Victoria Commercial Metal Roofing →03
Victoria Commercial Roof Repair
When your Victoria building springs a leak, you need a commercial crew that finds the failure point — not just the wet spot.
See Victoria Commercial Roof Repair →04
Victoria Commercial Roof Replacement
If you manage an aging Victoria building, here's how ARP calls recover versus full tear-off before your reroof starts.
See Victoria Commercial Roof Replacement →05
Victoria Commercial Storm Damage Roofing
Commercial storm damage in Victoria, TX — ARP documents hail, wind, and hurricane damage with condition reports and City of Victoria permits. Free inspection.
See Victoria Commercial Storm Damage Roofing →Book your free Victoria commercial roof assessment
Photo-documented, with a written condition report in hand — whether or not you hire us.
